Oppmerksomhet: Alle norske bestillinger vil bli sendt av Winston VW Veteran AS (Sandnes, Norge),
så fraktkostnader er nå mye lavere og alle lokale avgifter er nå inkludert i prisen. På store karosserideler må det beregnes leveringstid, og høyere Innenlandsfrakt.
Delene som er nevnt her, har en nær sammenheng med den valgte delen og blir ofte bestilt sammen med den valgte delen eller søkt etter.
Tips: Hvis du ikke får et godt søkeresultat når du skriver inn et søkeord, prøv en del som har noe med det å gjøre, hvis det er en relatert fane, er den søkte delen ofte nevnt der.
Bremse rens (spray)
Content: 500 ml Artikkelnummer : 50150
Useful information from Paruzzi magazine and from our YouTube channel :
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 08 ignition time of cylinder 1 In this video we will determine the ignition timing of cylinder 1. This mark will be needed to correctly position the distributor drive shaft during assembly, as well as for ignition advance adjustment once the Type 1 Volkswagen engine is rebuilt.
Engine overhaul - video 20 pushrod tubes With the cylinder heads out of the way, you can install standard pushrod tubes. But, disassembling the cylinder heads means replacing the gasket between cylinders and crankcase.
Engine overhaul - video 04 removing the distributor drive shaft We want to give extra attention in this video to the position of the distributor drive shaft of the VW Type 1 engines, . If the drive shaft of the distributor is not correctly mounted during the engine overhaul, problems can arise later with the adjustment of the ignition timing. Disassembling the drive shaft is then the only solution.
measure crankshaft end play The play is caused by wear of the engine, this is actually very normal, and will occur faster with performance engines. With normal use of standard VW engines in combination with a good maintenance of the engine, wear will not occur quickly.
Engine overhaul - video 11 the clutch To disassemble the flywheel, you will need to loosen the gland nut, we discuss that in video 12. But first you will need to disassemble the clutch. You can do that when the engine is on the workbench, or hanging from an engine mount. In this video we show various techniques and tools to disassemble the clutch of your Type 1 Volkswagen engine without damage.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.
Engine overhaul - video 13 replacing the crank seal During a complete engine overhaul, you will need to replace the crank seal. But replacement may also be necessary, when you discover an oil leak behind the flywheel, which will impair the operation of the clutch. We show in this video how to disassemble and reassemble the crank seal.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
the clutch: basic concept For a long time I wondered how the clutch in our Volkswagen Fastback worked, I was only six years old. I didn't understand very well that by releasing a pedal our VW started to drive spontaneously. Well, if you understand how disc brakes work, then the step to understanding how the clutch mechanism works is not far.