Do you have the product from the page mounted on your car? Take a clear picture or video of it and put it in the spotlights. This way your car gets admired by a lot of people and others can see what the product looks like. We reward your effort with a € 1,- discount code for every approved photo or video. Use the discount on your next order. Click here to upload your photo Click here to upload your video
Fits: Type-1 engines 8.1965 and later
Type-3 engines
CT/CZ engines
Waterboxer engines
These parts are supplied or included with the part you have selected now, you can use these parts to repair the selected part.
Rocker shaft shims for high-ratio rocker kit #1780 and #1781 (8 pieces)
Thickness: 0.254 mm
Inner size: 19.50 mm
Outer size: 25.40 mm Paruzzi number : 2992
Rocker shaft shims for high-ratio rocker (8 pieces)
for set #1780 and #1781
Thickness: 0.381 mm
Inner size: 19.50 mm
Outer size: 25.40 mm Paruzzi number : 2991
Rocker shaft shims for high-ratio rocker kit # 1780 and # 1781 (8 pieces)
Thickness: 0.762 mm
Inner size: 19.50 mm
Outer size: 25.40 mm Paruzzi number : 2990
The parts mentioned here have a close relationship with the selected part and are often ordered along with the selected part or searched for.
Tip: if you do not get a good search result when entering a keyword try a part that has something to do with it, if there is a related tab, the searched item is often mentioned there.
Assembly lube, tube
Content: 7 gram Paruzzi number : 50890
If the selected part does not apply to your Volkswagen type, check this list of the same parts that fit on other construction years or other types of cars.
Hi-ratio rocker kit 1: 25 to 1 chromoly (per pair)
Type-1 engines 8.1965 and later
Type-3 engines
CT/CZ engines
Waterboxer engines
Note:
Also use hardened valve stem caps #1739 Paruzzi number : 1780
Useful information from Paruzzi magazine and from our YouTube channel :
Engine overhaul - video 09 the fuel pump We will disassemble and reassemble the mechanical fuel pump from a VW Type 1 engine with carburetor in this video. The electric fuel pump is discussed in another video. The fuel pump pushrod and the fuel pump flange get extra attention in this video.
Engine diagnostics - video 02 BONUS defective rockers arm parts In video two of this series, we measured the rocker arm parts, and compared them to the wear limits listed by the VW workshop manual. In this video, we will show examples of rocker arm parts that are in less good condition than these of our AB 1300 engine from video two. This should help, to better diagnose the rocker arm parts.
Engine overhaul - video 20 pushrod tubes With the cylinder heads out of the way, you can install standard pushrod tubes. But, disassembling the cylinder heads means replacing the gasket between cylinders and crankcase.
oil seals All rotating parts fitted with bearings lubricated by oil or grease, such as crankshafts, transmission shafts, drive shafts, steering rods, etc., must be sealed. In our classic VW's we find two types of oil seals, namely the static and the dynamic (lip seal) oil seals.
Engine overhaul - video 10 the crankshaft pulley In this tenth video, we will show how to disassemble and reassemble the crankshaft pulley. We will use special tools for this, standard tools, as well as a homemade pulley puller. If you don't have the right tools and use the right technique, chances are you will warp the crankshaft pulley, you really don't want that. So watch this video carefully before you start this job.
Engine overhaul - video 05 install the distributor drive shaft This is the continuation of video 04, we are now going to install the distributor drive shaft, both on an already rebuilt Volkswagen Type 1 engine and on a split Type 1 crankcase. We pay a lot of attention to the correct positioning of the drive shaft at the beginning of this video series, because it is crucial to be able to adjust the ignition properly, later, when the engine is overhauled.
Engine overhaul - video 14 rockers and pushrods In this video we will show how to disassemble and reassemble the rocker arms and pushrods. We will discuss the diagnosis of the rockers and pushrods in our other video series, which deals with engine diagnosis. How to adjust the rockers, an action also known as shimming, can be seen in our video series on engine adjustment.
Engine diagnostics - video 01 crankshaft end play In the first video of this new series, we will look at how to measure the crankshaft end play. Measuring the crankshaft end play, will help you estimate if your engine needs a total overhaul. If the result of the measurement is greater than or equal to 0.15 millimeters, then the crankshaft clearance is too large, and a total engine overhaul is recommended.
finding the top dead center What does Top Dead Center (TDC) actually mean? If you study the theory of the operation of an internal combustion engine - or the "petrol engine" - it will become clear. Without going into too much detail about the theory, we have to talk about the otto cycle, better known as the four stroke cycle.
Engine overhaul - video 17 assemble cylinder heads In this video, we show you how to assemble the cylinder heads of a VW Type 1 engine, and what to pay particular attention to.